Contact
Hydrographic surveyor watching a survey launch at work

Hydrographic, Geophysical & Seabed Surveys

The seabed measured accurately, from the waterline down through the sediment.

Every marine development starts with an accurate picture of the seabed. Marine Trex plans and executes hydrographic and geophysical surveys that answer engineering questions directly: is there enough under-keel clearance, what is the seabed made of, where are the obstructions, how thick is the soft sediment above rock, and what has changed since the last survey.

Surveys are designed backwards from the deliverable. We select the survey order, line spacing, sensor suite and positioning method to meet the required total horizontal and vertical uncertainty, then process data through a documented workflow with full QC traceability. Results are delivered as engineering-ready surfaces, charts and GIS layers rather than raw files.

Coastal survey vessel moored in a harbour

Scope of services

Bathymetry

  • Multibeam echosounder (MBES) surveys for full-coverage bathymetry
  • Single-beam echosounder (SBES) surveys for channels, berths and shallow areas
  • Port, berth-pocket and approach-channel depth verification
  • Pre- and post-dredge surveys and volume computation

Geophysics

  • Side-scan sonar (SSS) for seabed features, debris and targets
  • Sub-bottom profiling (pinger, chirp, boomer, sparker)
  • Magnetometer and gradiometer surveys for ferrous objects and buried services
  • Seabed classification and ground-truthing with grab samples

Route & mapping

  • Pipeline and cable route surveys and corridor selection
  • Depth-of-burial and as-laid/as-built surveys
  • Underwater mapping, marine GIS and charting
  • 3D seabed modelling and change detection
Surveyor reviewing a 3D multibeam bathymetry model on screen
Autonomous underwater vehicle in its launch cradle on deck
Survey team monitoring multibeam acquisition screens

How we carry it out

01Survey design & uncertainty

Line planning and sensor selection are driven by a total propagated uncertainty (TPU) budget against the specified IHO S-44 order or client tolerance. Cross-lines, patch tests and bar or CTD checks are planned from the outset.

02Positioning & motion

GNSS with RTK, PPP or network corrections, integrated with an inertial navigation system for heave, pitch, roll and heading; vertical control is referenced to chart datum through tide gauges or ellipsoidal (GNSS) reduction with a validated separation model.

03Sound velocity control

Surface sound velocity is logged continuously and full-depth sound velocity profiles are acquired at intervals matched to the water-column variability typical of GCC coastal waters in summer.

04Geophysical interpretation

Side-scan mosaics, sub-bottom reflectors and magnetic anomalies are interpreted together, correlated with grab samples or geotechnical data, and reported as targets, horizons and seabed classes.

05Processing & QC

Data are cleaned and gridded in industry-standard hydrographic processing software with CUBE-type surface generation, uncertainty surfaces and documented QC at each step.

Equipment and methods

  • Multibeam echosounders (shallow-water, high-resolution)
  • Single-beam and dual-frequency echosounders
  • Side-scan sonars
  • Sub-bottom profilers (chirp, pinger, boomer, sparker)
  • Marine magnetometers and gradiometers
  • GNSS-aided inertial navigation systems
  • Sound velocity profilers, CTDs and tide gauges
  • Uncrewed surface vessels for shallow or hazardous areas

Equipment listed describes the technology used to deliver this service. Specific systems are selected for each project's requirements and site conditions.

Specifications and standards

Survey standard
IHO S-44 (6th Ed.): Exclusive, Special, 1a, 1b or 2 Order as specified
Vertical datum
Chart datum via tidal reduction or GNSS ellipsoid-referenced survey
MBES coverage
Typically 100–200 % coverage with overlap for full-bottom search
SSS frequency
Dual frequency, typically ~300–900 kHz for target detection
Outputs
Gridded surfaces, uncertainty grids, contours, S-57/GIS layers

Relevant codes, standards & guidance

  • IHO S-44 Standards for Hydrographic Surveys (6th Edition)
  • IHO C-13 Manual on Hydrography
  • IHO S-57 / S-100 data standards for charting deliverables
  • IMCA guidance for survey operations
  • Client and port-authority survey specifications

The governing standards, survey orders and acceptance criteria are confirmed for each project against the client's specification and the applicable national requirements.

Deliverables

  • Survey plans and method statements
  • Calibration (patch test) and QC reports
  • Bathymetric charts, digital terrain models and contours
  • Side-scan mosaics and target lists with images
  • Sub-bottom interpreted horizons and isopach maps
  • Magnetic anomaly maps and correlation reports
  • Route survey reports with alignment charts
  • GIS geodatabases and 3D seabed models

Where it is applied

Ports and harbours
Declared-depth surveys, pre- and post-dredge surveys and berth pocket checks for port authorities and terminal operators.
Offshore oil and gas
Pipeline and cable route surveys, platform site surveys and debris clearance surveys before rig moves.
Desalination and power
Bathymetry and seabed mapping for intake and outfall design and for sedimentation monitoring.
Marine infrastructure
Seabed and sub-seabed data for breakwaters, reclamation, bridges and waterfront developments.

Questions and answers

What is the difference between a hydrographic and a geophysical survey?

A hydrographic survey measures water depth and seabed shape, usually with multibeam or single-beam echosounders. A geophysical survey adds side-scan sonar, sub-bottom profiling and magnetometry to show what is on the seabed and what lies beneath it.

Which IHO S-44 order is needed for a port survey?

Harbours, berths and critical channels with limited under-keel clearance are normally surveyed to Special Order, and the 6th edition of S-44 adds Exclusive Order for the most demanding cases. The order is confirmed with the port authority or client specification.

When is multibeam preferred over single-beam?

Multibeam gives full seabed coverage and is preferred where objects, slopes or dredged profiles must be defined. Single-beam remains cost-effective for very shallow areas, reconnaissance and repeat profile lines.

What does a pipeline route survey include?

Typically bathymetry, side-scan sonar for seabed features and debris, sub-bottom profiling for shallow soils, a magnetometer for buried metallic objects and crossings, and seabed sampling to ground-truth the interpretation.

Related expertise