Contact
Green lateral navigation buoy marking a channel

Marine Navigation & Offshore Infrastructure

Aids to navigation, moorings and terminal infrastructure engineered for safe passage.

Safe navigation in GCC waters depends on aids to navigation (AtoN) that remain on station, on character and on air through summer heat, shamal winds and monsoon swell. Marine Trex engineers the complete AtoN system: the hull and its buoyancy reserve, the mooring that holds it, the lantern and power budget that keep it visible, and the electronic aids that place it on every bridge display.

The same mooring and load-path discipline extends offshore to catenary anchor leg moorings, CALM buoys and single point mooring terminals, where inspection and maintenance must be planned around tanker schedules and weather windows. Our teams combine marine engineering, survey positioning and diving or ROV inspection so that a buoy is not simply replaced, but verified, documented and returned to service with an auditable record.

Red lateral navigation buoy marking a channel

Scope of services

Aids to navigation

  • Lateral, cardinal, isolated-danger, safe-water and special-mark buoys
  • Marine lanterns, solar power systems and synchronised flashing
  • Condition surveys and modernisation of lighthouses, beacons and leading lights
  • AIS AtoN (real, synthetic and virtual) and RACON radar beacons
  • Channel markers, piled beacons and port approach marking schemes

Moorings & offshore infrastructure

  • Buoy installation, relocation, recovery and refurbishment
  • Offshore mooring systems: chain, wire and synthetic legs
  • Anchor chains, sinkers, clump weights, shackles and swivels
  • SPM / SBM (CALM) inspection, maintenance and hose-string support
  • Mooring dolphins, fenders and berth furniture condition surveys
Mooring anchors with chain and shackles ready for installation
Crew preparing mooring floats on the deck of a vessel

How we carry it out

01Mooring design & analysis

Static and quasi-dynamic mooring analysis for each buoy class using site water depth, tidal range, current and design wave conditions. Chain grade and diameter, scope ratio, sinker mass and holding capacity are selected with corrosion and wear allowances appropriate to the design life.

02Positioning & verification

Buoys and sinkers are placed against charted or design positions using RTK/PPP GNSS, with as-laid position, swing-circle and watch-circle checks recorded and reported to the competent authority.

03Light & power engineering

Lantern selection to required nominal range and character, solar array and battery autonomy sizing for the site insolation and duty cycle, and verification of rhythm, colour and intensity after installation.

04Underwater inspection

Diver or ROV inspection of mooring legs, chain-wear measurement at the touchdown zone and connecting hardware, sinker embedment and scour, marine growth and anode condition.

05SPM inspection & maintenance

Planned inspection of CALM buoy body, turntable and bearing, product swivel, anchor legs, under-buoy hoses and floating hose strings in line with operator procedures and OCIMF guidance.

Equipment and methods

  • Steel and polyethylene navigation buoys
  • LED marine lanterns with GNSS synchronisation
  • AIS AtoN transponders (Type 1/3) and RACONs
  • Stud-link and studless mooring chain, sinkers and clump weights
  • Load cells and chain calipers
  • RTK/PPP GNSS positioning
  • Inspection-class ROVs and surface-supplied diving spreads

Equipment listed describes the technology used to deliver this service. Specific systems are selected for each project's requirements and site conditions.

Specifications and standards

Buoyage system
IALA Maritime Buoyage System, Region A (GCC waters)
Lantern verification
Character, colour and nominal range checked post-installation
Positioning
Typical horizontal accuracy < 0.1 m RTK; < 0.5 m PPP
Chain assessment
Diameter loss measured against nominal and replacement criteria
AIS AtoN
Message 21 broadcast; real, synthetic and virtual configurations

Relevant codes, standards & guidance

  • IALA Maritime Buoyage System (Region A)
  • IALA Recommendations and Guidelines on AtoN design, lights and AIS AtoN
  • ITU-R M.1371 (AIS technical characteristics)
  • ITU-R M.824 (radar beacons)
  • OCIMF guidance for offshore marine terminals and SPM maintenance
  • API RP 2SK / DNV offshore standards for position mooring and mooring chain
  • Port and maritime authority requirements in each GCC state

The governing standards, survey orders and acceptance criteria are confirmed for each project against the client's specification and the applicable national requirements.

Deliverables

  • AtoN and mooring design reports with calculations
  • Installation method statements and risk assessments
  • As-installed position certificates and notices for charting
  • Lantern and AIS AtoN commissioning records
  • Chain-wear, hardware and anode inspection reports
  • SPM inspection reports with condition grading and repair recommendations
  • Planned maintenance schedules and spares lists

Where it is applied

Ports and harbours
Marking of new and deepened channels, turning basins and berth approaches, with re-marking after capital dredging.
Offshore oil and gas
Inspection and maintenance of SPM and CALM buoy moorings, hoses and marker buoys at export terminals.
Desalination and power
Marking of intake and outfall structures and exclusion zones to keep vessels clear.
Marine infrastructure
Temporary marking for construction zones, cable routes, reclamation works and wrecks.

Questions and answers

Which buoyage system applies in GCC waters?

Oman, Saudi Arabia, the UAE and Qatar use IALA Maritime Buoyage System Region A, in which port-hand marks are red and starboard-hand marks are green when entering from seaward.

How often should navigation buoys be maintained?

Intervals depend on the availability target set for the aid and on local fouling and corrosion rates. Typical programmes combine remote monitoring of lantern and position status with planned site visits to clean, inspect moorings and replace worn chain and shackles.

What does an SPM mooring inspection cover?

A typical inspection covers the buoy body and turntable, mooring hawsers, floating and subsea hoses, anchor chains and their touchdown points, the PLEM and the cathodic protection system, using a combination of surface checks, divers and ROV.

Related expertise